Meat refrigerated pork beef cold storage room

The most suitable temperature range for mushrooms is 18-20℃, and the most suitable growth temperature for the fruiting body stage is 12-16℃. In all stages of mushroom growth, temperature control is very important.Tell us your cold storage Length * Wide * High(m) and then we can send you full quotation sheet about all equipment you need !Voltage accept 220V/380/50~60Hz.

Whether your need is cold storage faclities , refrigeration equirpment for Icehouse, walk in freezer room cold storage or seafood storage, whole cooling system products we can provide and you just need to tell us : 1.The Length * Wide * High(m) of the cold room . 2. The room temperature you want ? Or what do you want to refrigerate ?  3. If there any other special requirement for voltage ?   

Whether your need is equipment for cold storage container , mini cold storage for logistics cold chain system or walk in freezer cold storage , whole cooling system products we can provide and you just need to tell us :1.The Length * Wide * High(m) of the cold room .2. The room temperature you want ? Or what do you want to refrigerate ? 3. If there any other special requirement for voltage ? 

Whether you want any equipment for your vegetable or fruit refrigerated cold storage which over -5°C , we can provide whole cooling system products include condensing unit, air cooler, PU panel ,door and all accessories to you , and you just need to tell us : 1.The Length * Wide * High(m) of the cold room . 2. The room temperature you want ? Or what do you want to refrigerate ?  3. If there any other special requirement for voltage ?   

We provide refrigeration equipment for all cold room system need and support working temperature from -70°C to +60 °C . Hotels, restaurants , supermarkets, food, health, medicine , agriculture and other industries all welcome to send us inquiry to check.

SEMI-HERMETIC For standard refrigerantsUniversal and environmentally friendly: ECOLINE reciprocating compressors offer high cooling capacity with minimal energy requirements and are optimised for HFC, HFO and low-GWP refrigerants. The optional VARISTEP mechanical capacity control offers high part-load efficiency in medium and low temperature application.

Air cooled condenser is specially designed for Freon refrigeration equipment and cooled by air. XMK FNF series is suitable for R134a, R22, R404a, R407 and other refrigerants, widely used in freezing, refrigeration, air conditioning, heat pumps and industrial refrigeration. Fan blower support 350mm to 500mm.

XMK-5201 1/2 ODF Oil Separator RefrigerationWe oil separator has the great oil-separating capacity.The mixed gaseous refrigerant get into oil separator from compressor,carring oil to get through stainless steel mesh inlet.The oil particles collide and become heavier,impacting on the inwall and intermediate clapboard ultimately.The separated oil drop on the bottom of separator,when them accumulate to a certain amount,the oil will get back to compressor crankcase automatically through the pressure differential  ball float needle valve device.ModelConnector sizeXMK-52011/2 ODFXMK-52025/8 ODFXMK-52037/8 ODFXMK-52041-1/8 ODFXMK-52051-3/8 ODFXMK-62031-3/8 ODFXMK-62041-5/8 ODFXMK-62052-1/8 ODFProduction Introduction:The oil separator should be installed vertically and pre-charge the oil before installing oil separator,the oil should be same as the oil in the compressor crankcase.In the actual piping system,the excessive loads or vibration at the inlet and outlet should be prevented.Oil storage separator must be fixed in the mounting pin connections. Design features:1,Extra length multiayer filter mesh desgin will buffer the mixed gaseous refrigerant greatly.2,The installation of clapboard and spacer palte devide the space into three rooms,improving the efficiency of oil separating greatly.3,In practical application,the vibration of unit might affect ball float installation stability,so the clapboard and spacer plate could reduce the vibration og it.4,Reasonable stainless steel ball float installation desgin remove the crash of ball float and oil return pipe which reduced the noise.5,The installation of magner on the bottom absorb the remaining iron dust in the system helpfully.